Garage Door Opener Repair and Installation in Fairfax, VA

An opener does not lift the door. It steers a door that the springs already balanced.

We are a matching service, not a contractor. Opener work goes to licensed garage door companies serving Fairfax County, and you hold the contract and the warranty with the firm you hire. Most opener calls are one of three things: a unit at the end of its life, a safety device out of adjustment, or a door that is out of balance and dragging the motor down with it.

Four drive types, and which one fits the house

DrivePublished unit priceWhere it suits
Chain$150 to $300Detached garage, where noise does not carry
Belt$180 to $450Attached garage under a bedroom
Screw$200 to $400Fast opening, moderate noise, low maintenance
Jackshaft$400 to $800High lift or torsion side mount, ceiling kept clear

Angi publishes those unit prices and puts installation at $65 to $85 an hour for two to six hours of work, with a national average installed cost of $379 and a range of $218 to $540.

The choice is mostly about the room above the car. A chain drive is the cheapest and the noisiest, and in a townhouse with a bedroom over the garage that noise arrives at six in the morning. A jackshaft mounts on the wall beside the torsion shaft instead of hanging from the ceiling, which is the right answer when the ceiling is used for storage or the door is on high lift track.

Safety reverse is a standard, not an option

Residential openers sold in the United States have to carry two entrapment protections: an inherent reversing system inside the unit, and an external device, which in practice is a photo eye or a door edge sensor. Under the federal rule that adopts UL 325, the inherent system has to reverse a closing door within two seconds. UL describes the photo eye as mounted on the track frame roughly six inches above the floor.

The test is simple and the manufacturer expects it monthly. Put a solid object about an inch and a half high, or a two by four laid flat, in the door's path and close it. The door should stop and reverse on contact. If it presses down and keeps going, the opener needs adjustment or replacement before the door is used again.

The manual release cord is the other required part. It disconnects the door from the opener in a power cut. Test it with the door closed, because releasing a door that is open on weak springs lets it drop.

Horsepower, weight and duty

Angi puts entry level half horsepower units from $100 and heavy duty two horsepower units at $300 to $400, and the rule that follows is simple: the heavier the door, the more motor it takes. A single steel door at roughly 125 pounds is half horsepower work. A double insulated door near 200 pounds, with glass, is not.

Duty matters as much as weight. A door that cycles eight or ten times a day on a builder grade opener is a motor that runs hot every morning. If the garage is the front door of the house, spend the difference on the opener rather than on the trim.

One more number matters and it is not on the box. A door that is out of balance feels heavy to the motor even when the motor is correctly sized, so a technician should move the door by hand with the opener disconnected before blaming the unit. A door that will not stay at waist height needs springs, not horsepower.

Repair, replace, and the wiring question

Home Depot lists opener repair parts at about $149, a replacement opener at $390 and a replacement remote at $35. A repair makes sense when the unit is otherwise sound: a gear, a capacitor, a logic board, a remote that will not pair. It stops making sense when the motor is noisy, the travel limits drift and the unit is past its service life, because the second failure follows the first closely.

Installation is where the county enters the conversation. Fairfax County Land Development Services lists new electrical fixtures and equipment, and replacement of electrical equipment, as permit work, so a new circuit or a new outlet in the garage is an electrical permit, not part of the opener install. Ask the installer who is pulling it. If the answer is nobody, call Land Development Services at 703-222-0801 before the work starts.

Frequently asked questions

My opener hums but the door does not move. What is wrong?

Usually the door, not the opener. A broken spring, a snapped cable or a door off its track leaves the motor turning against a load it cannot lift. Disconnect the opener and have the door checked first.

How long does opener installation take?

Two to four hours for a straightforward swap on a standard door, longer where a new rail has to be cut, a new bracket has to be mounted on brick, or a circuit has to be added. Angi quotes two to six hours of labor across the range.

Do I need a new opener when I buy a new door?

Not always, but the unit has to be rated for the new door's weight and has to pass the reverse test. A heavier door, or a taller opening that needs a longer rail, is the usual reason both are replaced together.

Related

Sources

Call (571) 704-8247Book Now